Run the hot side at two or three different taps to learn whether the whole house is cold or just one fixture. Whole-house cold water points to the heater: on an electric model reset its breaker once, and on a gas model see whether your other gas appliances work. A single cold tap is a fixture problem. Either way, a plumber takes it from there.

Key facts
- First action
- Test hot water at several taps
- Electric heater
- Reset its breaker one time
- Gas heater
- Check other gas appliances; leave the heater's controls alone
- Gas service problem
- CPS Energy, 210-353-4357
- License
- Texas State Board of Plumbing Examiners
- Gas tank heater, installed
- $1,000–$2,700 (national, Fixr)
Before you call
- More than one tap. Kitchen, a bathroom sink and a tub. Let each run a full minute. Cold everywhere means the heater; cold at one place means that faucet or shower valve.
- Recent heavy use. Back-to-back showers, laundry and a dishwasher can drain a tank. Wait an hour with no hot water running and test again.
- Breaker for an electric heater. If it tripped, switch it Off, then On, once. A second trip is a fault, not bad luck.
- Other gas appliances. If the stove or furnace also has no gas, the problem is the supply and not the heater.
- Floor around the tank. Any puddle or rust trail changes the diagnosis; see water heater leaking.
What to tell the company
- No hot water at all, lukewarm water, or hot water that runs out fast.
- Gas or electric, tank or tankless, and the age on the label.
- Whether the breaker had tripped and whether it held after one reset.
- Whether other gas appliances are working.
- Any leak, rumbling noise or discolored water.
Limits of a homeowner check
Stop and call a pro when:
- The breaker trips again.
- There is water at the base of the tank.
- A gas heater has gone out. Relighting and gas controls are not on this list on purpose.
- You smell gas: leave, then call 911 and CPS Energy at 210-353-4357 from another location.
- Hot water turns rusty or smells bad.
CPS Energy and gas supply
CPS Energy delivers natural gas as well as electricity in San Antonio. When every gas appliance is out, report it as a service problem on 210-353-4357 and hold off on the plumber.
Repair or replacement
A failed heating element or control is a repair. A tank that leaks or has reached the end of its life is a replacement. There is no local repair price in this guide. For a new tank-style gas heater, Fixr's national installed range is $1,000 to $2,700, and CPS Energy's current rebate list includes nothing for water heaters.
Permit and license
For a same-location replacement, city Information Bulletin 121c has the plumber obtain the permit within three working days after the job. The city's residential permits page lets a homeowner apply for a plumbing permit only for an existing homestead where the owner personally does the work. Plumbing licenses come from the Texas State Board of Plumbing Examiners; its site links to a public license search.
Want a price for your home? Call a local plumber for a written quote.
Phone line opening soonWhat a repair usually costs
National ranges from cost publishers, not San Antonio quotes. The fault decides the price, so ask for it in writing before work starts.
| Job | National range | Source |
|---|---|---|
| Water heater repair | $150 to $750 | Fixr, updated Aug 2025 |
When you call: 4 questions to ask
- What's the trip or diagnostic fee, and is it applied to the job?
- Is the price flat-rate or hourly, and what's the total before you start?
- Will you file the city permit for this job?
- What's your Texas State Board of Plumbing Examiners license number?
A fair written quote shows the parts list, labor, permit, haul-away of old equipment, and the warranty in writing. Check any contractor's license on the TDLR license search before work starts.
What happens when you call
- You're connectedStraight to a local plumber that serves your area and takes calls like yours.
- You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.
Common questions
Why do I suddenly have no hot water?
On an electric heater the common causes are a tripped breaker or a failed element. On a gas heater the burner may have gone out or the gas supply may be interrupted. A tank emptied by heavy use recovers on its own within an hour or so.
Who do I call for no hot water in San Antonio?
A plumber, in most cases. If all your gas appliances are down, call CPS Energy at 210-353-4357 first, because the heater cannot run without supply.
Should I relight the water heater myself?
This guide leaves that to a plumber. It keeps homeowner checks to taps, breakers and looking for leaks, and stays away from gas controls.
How long should a tank take to reheat?
It varies with tank size and fuel, and our sources give no figure. If an hour without use brings no warm water, book a visit.
Related guides
Sources
- CPS Energy: Contact us
- CPS Energy: Natural gas safety FAQ
- City of San Antonio Development Services: Information Bulletin 121c
- City of San Antonio Development Services: Residential permits
- Texas State Board of Plumbing Examiners: License types
- Fixr: Gas water heater cost
- CPS Energy: Residential rebates and programs
Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.