Local Repair FinderColorado Springs home repair guide

Furnace igniter or flame sensor: checking the quote

Colorado Springs & El Paso County · Reviewed November 2026 · Checked against 4 public sources

Want a second opinion on a quote?

Talk to a local heating & cooling pro now. Free, no obligation.

Phone line opening soon
  • Free to call
  • No obligation
  • Local Colorado Springs companies
  • Ask for a written quote

Have this ready when you call

  • Your address
  • What the system is doing (no heat, no cooling, a noise, a leak)
  • Roughly how old the unit is

The furnace clicks and the inducer runs but it never lights (igniter), or it lights and shuts off within seconds (flame sensor). An igniter typically costs $150–$350 installed in 2026; a flame sensor replacement $75–$250, and a dirty sensor can often just be cleaned. The two parts fail in different ways, so ask which one was found and how.

Key facts

Fair range
$150–$350
Ask to see
Ask to see the old igniter.
Extra most worth questioning
A new furnace

Both of these are wear parts, and neither one is a reason to replace a furnace. A failed igniter is usually cracked or won't glow. A flame sensor is judged by its flame signal, read in microamps, and a dirty one can often be cleaned instead of swapped.

That makes the evidence for this job small and easy to show: the old part in your hand, or a reading taken before and after.

What the technician can show you

  1. Ask to see the old igniter. A failed one is usually cracked or doesn't glow; the tech can show you with the furnace running.
  2. For a flame sensor, ask whether it was cleaned or replaced, and what the flame signal reading (in microamps) was before and after.
  3. Ask what else was checked: the filter, the pressure switch and the vent pipes. A blocked vent or dirty filter can cause the same symptoms.

Compare your igniter or sensor quote

Typical range: $150–$350.

Igniter vs sensor pricing

An igniter typically costs $150–$350 installed in 2026; a flame sensor replacement $75–$250, and a dirty sensor can often just be cleaned. In Colorado Springs, most HVAC repairs run $150–$650 (ConsumerAffairs).

Told it's more than an igniter or sensor? Another local heating pro can take a second look.

Phone line opening soon

Extras that ride along on a no-heat call

ExtraFair whenPush back when
A new furnaceThe heat exchanger is confirmed cracked, or the furnace is about 15+ years old and needs a major part.The only failed part is an igniter or flame sensor. These are wear parts, not a reason to replace.
A maintenance planYou'd have paid for a yearly tune-up anyway and the plan price is about the same.It's presented as required to get today's repair done, or the price isn't written down.
Duct cleaning or UV lightsThere's visible debris in the ducts or a specific air-quality problem.It's offered on a no-heat call with no evidence shown.

Ask these before the furnace is closed up

  1. What part failed, and can I see it?
  2. Is the diagnostic fee credited toward the repair?
  3. What was the flame signal or test reading?
Warning signs on a no-heat visit
  • Being told the furnace is unsafe without a reading, photo or written red-tag.
  • A replacement quote handed over before the furnace has been diagnosed.

When you call: 4 questions to ask

  1. Is the diagnostic or trip fee credited toward the repair?
  2. Will you size a new system with a load calculation and set it up for our altitude?
  3. Is the PPRBD mechanical permit included, and what's your PPRBD license number?
  4. Does this model qualify for the Colorado Springs Utilities rebate, and who files it?

A fair written quote shows model numbers and efficiency, altitude setup, the permit and inspection, removal of the old unit, and parts and labor warranty. Check any contractor's license on pprbd.org before work starts.

What happens when you call

  1. You're connectedStraight to a local heating & cooling pro that serves your area and takes calls like yours.
  2. You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.

Common questions

How much does it cost to replace a furnace igniter in Colorado Springs?

Most igniter replacements run about $150–$350 installed in 2026, and most HVAC repairs in Colorado Springs fall between $150 and $650 (ConsumerAffairs). Emergency or after-hours calls cost more.

Can a dirty flame sensor be cleaned instead of replaced?

Often, yes. If the furnace lights and then shuts off within seconds, a technician will usually clean the sensor first. Replacement makes sense if it's cracked or still fails after cleaning.

Related guides

Sources

  1. Filterbuy: Furnace repair cost by part (Oct 2026)
  2. ThePricer: Furnace ignitor replacement cost (Angi 2026 data, Oct 2026)
  3. ConsumerAffairs: HVAC companies in Colorado Springs: 2026 repair and replacement costs
  4. Trane: Repair or replace: the $5,000 rule

Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.