A breaker trips to protect the wiring. Most often the circuit is carrying too much at once. Unplug everything on it, reset the breaker a single time, then add devices back one by one. If it trips with nothing plugged in, trips instantly, or the panel feels warm or smells burnt, leave it off and call an electrician. Utah licenses electricians through DOPL, and Salt Lake City requires a permit to alter electrical systems.

Key facts
- Safe limit
- One reset, with the circuit unplugged
- Electrical license
- E200 General Electrical or E201 Residential Electrical (Utah DOPL)
- Permit
- City requires one to install or alter electrical systems
- Panel upgrade to 200 amps
- Most homeowners pay $1,300–$3,000 to upgrade to 200 amps (This Old House, national)
- Whole house dark
- Rocky Mountain Power, 1-877-508-5088
What is it usually?
| Symptom | Likely cause | Your move |
|---|---|---|
| Trips when the microwave and kettle run together | Overloaded circuit | Move one appliance to another outlet |
| Trips the instant you reset it | Short circuit or ground fault | Leave it off. Call |
| Trips whenever one device is plugged in | That device is faulty | Stop using the device |
| Bathroom or kitchen outlets dead, breaker looks fine | A GFCI outlet has tripped | Press Reset on the outlet |
| Trips at random, panel warm or buzzing | Worn breaker or loose connection | Hands off. Call today |
| Trips when the AC or furnace starts | Equipment drawing too much current | One reset. Then an HVAC or electrical visit |
What can you safely check yourself?
- Work out what the breaker feeds. See which lights and outlets went dead. Read the label next to the breaker if there is one.
- Unplug it all. Every lamp, charger, heater and appliance on that circuit. Switch the lights off too.
- Reset one time. Push the handle firmly to Off, then to On. Only the breaker handle. The metal cover on the panel stays screwed on.
- Add things back slowly. Plug in a single item and wait a minute. Then the next. Whatever you added just before it trips is your suspect, or your tipping point.
- Look for a GFCI. Outlets with Test and Reset buttons guard kitchens, baths, garages and outdoor plugs. Press Reset. One of these can cut power to several outlets downstream.
- Spread the load. Space heaters, hair dryers, microwaves and vacuums are heavy users. Run them on different circuits, or not at the same moment.
When should you stop and call a pro?
- It trips with every device unplugged.
- It trips again right after your single reset.
- The breaker, the panel door or an outlet feels hot.
- You notice a burning smell, scorch marks or a buzzing sound.
- Lights dim or flicker across several rooms.
- The main breaker is the one tripping.
- Water has been anywhere near the panel.
Smoke or flames are a 911 call. Otherwise leave the breaker off and wait. Repeated resets wear the breaker and heat the fault.
Want a price for your home? Call a local electrician for a written quote.
Phone line opening soonIs it your house or the power company?
A tripped breaker is on your side. If every room is dark and no breaker has moved, look outside. Are the neighbors dark too? Rocky Mountain Power supplies electricity in Salt Lake City and takes outage and downed-wire reports at 1-877-508-5088. Another utility on your bill means another number.
Does weather play a part?
Demand does. The airport's normal January low is 24.2 °F and its normal July high is 94 °F, per NOAA's 1991-2020 normals. Space heaters come out in one season and window units or portable coolers in the other. Each can use most of a circuit on its own. Trips that follow the weather are usually load, not a wiring fault.
Does the repair need a permit?
Salt Lake City Building Services says installing or altering electrical systems requires a permit. Adding a circuit or replacing a panel alters the system. The FAQ does not list small repairs such as a single breaker swap, so this guide has no answer on those. Have the electrician tell you, in writing, whether your job needs one.
Which license should the electrician hold?
Utah's DOPL licenses journeyman and master electricians. Electrical contractors hold E200 General Electrical or E201 Residential Electrical. Look them up on the DOPL lookup and check that the license is active. Phone help is at 801-530-6628.
What will it cost?
This guide has no verified Salt Lake City price for diagnosing a circuit or replacing a breaker. Ask for the call-out fee before the visit. If the answer turns out to be a bigger panel, This Old House says most homeowners pay $1,300 to $3,000 to upgrade to 200 amps. That is a national range. The panel upgrade page covers it. Thinking about a heat pump? Rocky Mountain Power's 2026 tariff lists incentives of up to $2,500, and it is worth asking whether your panel can carry one.
What a repair usually costs
National ranges from cost publishers, not Salt Lake City quotes. The fault decides the price, so ask for it in writing before work starts.
| Job | National range | Source |
|---|---|---|
| Replacing a circuit breaker | $100 to $260 | HomeGuide |
When you call: 4 questions to ask
- What's your Utah DOPL electrical license number?
- Will you pull the Salt Lake City permit and book the inspection?
- Will the panel have room for a heat pump or EV charger later?
- Is there a trip fee, and is it credited if I go ahead?
A fair written quote shows the panel or parts, labor, permit and inspection, and any wiring fixes priced separately. Check any contractor's license on Utah's DOPL lookup before work starts.
What happens when you call
- You're connectedStraight to a local electrician that serves your area and takes calls like yours.
- You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.
Common questions
Why does my breaker keep tripping?
Usually the circuit is overloaded. Less often there is a short circuit, a ground fault, a failing appliance or a worn breaker. Unplugging everything and resetting once helps you tell which.
Is it safe to keep resetting a breaker?
No. Reset it once with the circuit unplugged. If it trips again, leave it off. Repeated resets can overheat the wiring at the fault.
How do I find out what is tripping my breaker?
Unplug everything on the circuit, reset, then plug items back in one by one, waiting a minute each time. The item that causes the trip, or pushes the load over, is the clue.
Do I need a permit to replace an electrical panel in Salt Lake City?
Salt Lake City says installing or altering electrical systems requires a permit. Replacing a panel alters the system. The city's FAQ does not name panels word for word, so confirm with your electrician.
Related guides
Sources
- Rocky Mountain Power: Outages and safety
- Salt Lake City: 100% renewable energy community goal
- NOAA NCEI: 1991-2020 monthly climate normals, Salt Lake City International Airport
- Salt Lake City Building Services: Frequently asked questions
- Utah Legislature: Utah Code 58-55-301, license classifications
- Utah Division of Professional Licensing: Apply for a general contractor license
- This Old House: Cost to upgrade an electrical panel
- Utah Public Service Commission: Rocky Mountain Power Schedule 111 tariff filing (2026)
Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.